BGXSV - ASPHALT VARNISH, BLACK, #17038, #40 VITANIC
- MSDS: BGXSV
- Manufacturer: FARWEST PAINT MANUFACTURING CO
- Product Name: ASPHALT VARNISH, BLACK, #17038, #40 VITANIC
- National Stock Number: 8010-00-160-5856
Product Identification
Product ID:ASPHALT VARNISH, BLACK, #17038, #40 VITANIC
MSDS Date:02/27/1987
FSC:8010
NIIN:00-160-5856
MSDS Number: BGXSV
Responsible Party
TUKWILA, WA 98168
US
Emergency Phone: (206) 941-1619
Info Phone: (206) 244-8844
Cage: 2F266
Contractor
Telephone: 206-244-8844
Cage: 6F266
Ingredients
ALIPHATIC HYDROCARBON (VAPOR PRESSURE 2.0 MMHG @ 68F)
Fraction By Weight: 48-53%
OSHA PEL 500 PPM
ACGIH TLV: 100 PPM
AROMATIC HYDROCARBON (VAPOR PRESSURE 22 MMHG @ 68F)
Fraction By Weight: 1-5%
ACGIH TLV: 100 PPM
ETHYLENE GLYCOL MONO N-PROPYL ETHER (VAPOR PRESSURE 1.3
Fraction By Weight: 7%
ACGIH TLV: 25 PPM
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Effects of Overexposure:EYES:CAN CAUSE SEVERE
IRRITATION,REDNESS,TEARING,BLURRED VISION. SKIN:PROLONGED OR
REPEATED CONTACT CAN CAUSE MODERATE IRRITATION,DEFATTING,
DERMATITIS. BREATHING:EXCESS INHALATION OF VAPORS CAN CAUSE NASAL
& RESPIRATORY IRRITATION
DIZZINESS,WEAKNESS,FATIGUE,NAUSEA,HEADACHE,POSS UNCONSCIOUSNESS &
ASPHYXIATION.**
Medical Cond Aggravated by Exposure:**SWALLOWING: CAN CAUSE
GASTROINTESTINAL IRRITATION, NAUSEA, VOMITING & DIARRHEA.
ASPIRATION OF MATERIAL INTO THE LUNGS CAN CAUSE CHEMICAL
PNEUMONITIS WHICH CAN BE FATAL.
First Aid
First Aid:SKIN:THOROUGHLY WASH EXPOSED AREA W/SOAP & WATER. REMOVE
CONTAMINATED CLOTHING.LAUNDER CLOTHING BEFORE REUSE.EYES:FLUSH
W/LARGE AMOUNTS OF WATER,LIFTING LIDS OCCASIONALLY, SEEK MEDICAL
ATTENTION. SWAL LOWING:DO NOT INDUCE VOMITING,KEEP PERSON WARM,
QUIET, SEEK MEDICAL ATTENTION. ASPIRATION OF MATERIAL INTO THE LUNG
CAUSES CHEMICAL PNEUMONITIS. INHAL:FRESH AIR;OXYGEN; OR ARTIFICIAL
RESPIRATION.
Fire Fighting
Flash Point:100F/37.8C
Lower Limits:1.0
Extinguishing Media:FOAM, DRY CHEMICAL, CO2.
Fire Fighting Procedures:SELF-CONTAINED BREATHING APPARATUS WITH A FULL
FACEPIECE OPERATED IN PRESSURE DEMAND OR OTHER POSITIVE PRESSURE
MODE.
Unusual Fire/Explosion Hazard:NEVER USE NEAR OR AROUND WELDERS OR
CUTTING TORCHES, DRUM (EVEN EMPTY) BECAUSE PRODUCT (EVEN JUST
RESIDUE) CAN IGNITE EXPLOSIVELY.
Accidental Release
Spill Release Procedures:SMALL SPILL:ABSORB LIQUID ON
PAPER,VERMICULITE,OTHER ABSORBENT MATERIAL & TRANSFER TO HOOD.
LARGE SPILL:ELIMINATE IGNITION SOURCES,PERSONS NOT WEARING
PROTECTIVE EQUIP SHOULD BE EXCLUDED FROM AREA. ST OP SPILL AT
SOURCE.DIKE AREA TO PREVENT*
Neutralizing Agent:*SPREADING, IF RUNOFF OCCURS NOTIFY PROPER
AUTHORITIES AS REQUIRED.
Handling
Handling and Storage Precautions:CONTAINERS OF PRODUCT MAY BE HAZARDOUS
WHEN EMPTY SINCE EMPTY CONTAINERS RETAIN PRODUCT RESIDUES ALL
HAZARD PRECAUTIONS GIVEN MUST BE OBSERVED.
Other Precautions:ENVIRONMENTAL CONTROL. OSHA REGULATIONS ALSO PERMIT
OTHER NIOSH/MSHA RESPIRATORS UNDER SPECIFIED CONDITIONS.
ENGINEERING OR ADMINISTRATIVE CONTROLS SHOULD BE IMPLEMENTED TO
REDUCE EXPOSURE.
Exposure Controls
Respiratory Protection:IF TLV OF PRODUCT IS EXCEEDED, A NIOSH/MSHA
JOINTLY APPROVED AIR SUPPLIED RESPIRATOR IS ADVISED IN ABSENCE OF
PROPER ENVIRONMENTAL CONTROL. ENGINEERING OR ADMINISTRATIVE
CONTROLS SHOULD BE IMPLEMENTED TO REDUCE EXPOSURE.
Ventilation:PROVIDE SUFFICIENT MECHANICAL VENTILATION TO MAINTAIN
EXPOSURE BELOW TLV(S).
Protective Gloves:WEAR RESISTANT GLOVES: NITRILE RUBBER.
Eye Protection:CHEMICAL SPLASH GOGGLES.
Other Protective Equipment:WEAR IMPERVIOUS CLOTHING AND BOOTS TO
PREVENT REPEATED OR PROLONGED SKIN CONTACT.
Work Hygienic Practices:KEEP WORK AREA CLEAN AND FREE FROM LEAKS AND
SPILLS. ALWAYS WASH HANDS W/SOAP & WATER BEFORE HANDLING FOOD OR
DRINK.
Supplemental Safety and Health
Chemical Properties
Boiling Pt:B.P. Text:300-410F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:NIL
Appearance and Odor:JET BLACK THIN LIQUID WITH A MILD PETROLEUM ODOR.
Percent Volatiles by Volume:63
Stability
Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM OPEN FLAMES, SPARKS AND
HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.
Conditions to Avoid Polymerization:KEEP AWAY FROM OPEN FLAMES,SPARKS
AND HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.
Disposal
Waste Disposal Methods:DESTROY BY LIQUID INCINERATION. CONTAMINATED
ABSORBENT MAY BE DEPOSITED IN A LANDFILL IN ACCORDANCE WITH
LOCAL,STATE AND FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.